What the tool does
It opens a video or audio file in your browser and pulls out the sound. Most phone videos and common audio formats open directly.
Some video containers need ffmpeg.wasm. The page then downloads that library (about 32 MB) from jsDelivr once and checks its SHA-256 fingerprint before running it. Your file is never sent anywhere.
You see the whole recording as a waveform and a spectrogram. Drag across the picture to select a call, play it back, and adjust the start and end to a tenth of a second.
Each clip is saved as a 16-bit WAV file. The original file’s metadata, such as creation time, device and location tags, is not carried over.
Why trim before identifying?
Sound identifiers judge a clip by what is in it. Long stretches of talk, wind or traffic add noise and can bury a quiet call.
Merlin’s own guidance is to get clear recordings and trim noise from the start and end eBird Help: Merlin Sound ID best practices (read 17 Nov 2026).
Merlin can import mp3, m4a and wav files eBird Help: Merlin Sound ID (read 17 Nov 2026). It does not list video, so pulling the soundtrack out first is the reliable route.
How to use it
- Drop the file. Keep the original: re-uploads and screen recordings lose quiet sounds.
- Pick “0–12 kHz” for birds. Look for short, repeated marks above the band where voices sit.
- Drag across one call or a short run of calls. Press Play to check it by ear.
- Add it to the clip list. Repeat for each different call you hear.
- Download the clips and run each through two identifiers. Record which tool suggested what, and with what confidence.
For batch work, split a long selection into 3- or 5-second pieces and run the folder through BirdNET-Analyzer.
What the settings do
- Mono mixes the channels into one. Most identifiers work in mono anyway, and the file is half the size.
- Sample rate. Browsers decode audio at their own rate, usually 44.1 or 48 kHz, and the page shows which. Choose another rate to convert with the browser’s resampler.
- Cut rumble applies a high-pass filter. It helps with wind and traffic under bird calls. It also removes mains hum and aircraft tones, so leave it off for that work.
- Normalise raises the clip so its loudest point sits just below full scale. It does not compress or change the sound’s shape.
- Fade adds a 10 ms fade at each end to stop clicks at the cut.
How we tested it
We built a 20-second test recording: a chirp series at 3 to 5 kHz, speech-like noise and a 60 Hz hum. We saved it as WAV, as a WebM video and as an MP4 video.
In Chromium, each opened and showed the chirps on the spectrogram. A clip cut from 4.0 to 7.5 seconds came out 3.5 seconds long, within one sample.
With “Cut rumble below 500 Hz”, the 60 Hz hum dropped by more than 40 dB while the chirps stayed within 1 dB. A split into 3-second pieces produced the expected number of files in a valid ZIP.
What it cannot do
- It does not identify species. It prepares clips for the tools that do.
- It cannot restore detail a re-upload already removed. Compressed audio often loses quiet, high calls.
- Very long files use a lot of memory. Recordings over 60 minutes are refused; trim them in another program first.
- Some files with unusual codecs may not open even with ffmpeg.wasm.
To lower location clues in your own recordings before you post, use the Doppler Scrubber.
Frequently asked questions
How do I get the audio out of a video for bird identification?
Drop the video into Audio Rip & Trim, select the part with the calls, and save it as a WAV file. Then import that file into Merlin or upload it to BirdNET.
Is my file uploaded?
No. Everything runs in your browser. For some video formats the page downloads the ffmpeg.wasm library from jsDelivr, but your file stays on your device.
Which file formats work?
Most phone videos (MP4, MOV) and common audio formats (WAV, MP3, M4A, OGG, FLAC, WebM) open directly. Other containers are converted with ffmpeg.wasm.
Why save as WAV instead of MP3?
WAV is uncompressed, so no detail is lost when you save. Merlin imports WAV, and BirdNET reads it.
What clip length works best for bird ID?
Short clips around the calls. Merlin advises trimming noise from the start and end. For batch analysis, split long sections into 3- or 5-second pieces.
Does the clip keep the original file’s metadata?
No. The WAV files contain only the sound, with no creation time, device or location tags.